Rihoo Industry (Hongkong) Co.,Limited
Contact Us

Factory Address: No.15, Yangjia, Xu Village, Wanshi, Zhuangshi Street, Zhenhai District, Ningbo, Zhejiang, 315201, China
Tel:+86-574-87626048
Fax:+86-574-87626048
Email: sales@rihooindustry.com
Website: www.rihooindustry.com

Track Roller Bearings Smooth Bad

Track Roller Bearings Smooth bad

Crawler roller bearings using water-soluble cutting fluid, the user will be in the machine maintenance and management efforts 

to control the generation of corrosion, and even eliminate the corrosion. In order to avoid the corrosion of water on the metal surface, should always stop the machine on the oil smooth oil, the important parts of the machine smear grease.

Crawler roller bearings in the correct use, can have a long life.If prematurely show damage, it may be due to selection errors, the use of improper or smooth bad formation.

Therefore, in the device bearing, we need to record the machine variety, device parts, the use of conditions and around with. After the study to summarize the type of bearing damage, attack the use of the environment, to prevent similar situation again.

Accurately control the concentration of cutting fluid, when the machine is working, with a cutting fluid to clean the appearance of clean machine, but also to open the machine shield to demolish the machine work area wet air. In order to avoid the occurrence of electric erosion, should be applied in the metal surface coating a layer of waterproof grease. In order to prevent the breeding and reproduction of bacteria, should regularly clean or change the cutting fluid, the timely elimination of chips, but also to use soft water ) Dilute the cutting concentrate.

Cylindrical roller bearings in addition to excellent quality, but also belong to the very fine parts, both high-performance bearings, if used in the course of improper use, not only achieve the desired performance results, and it is easy to damage the bearing, in terms of smooth Certainly have to pay attention.

First, the use of the device should be careful not to allow serious stamping, not allowed to use a vertical hit the bearing, do not allow rolling through the transmission pressure.

Second, the use of appropriate and accurate device tools as far as possible the use of special tools, try to prevent the use of cloth and short fibers and the like.

Third, try to adhere to the bearing and its surrounding environment clean even the naked eye can not see the smile dust into the bearing, will increase the bearing wear, vibration and noise.

Fourth, to avoid the corrosion of the bearing directly by hand to take the bearing, it is necessary to wash away the hands of the liquid, and coated with high-quality mineral oil and then stop the operation, especially in the rainy season and summer to pay attention to rust. Under certain operating conditions, the track roller bearings can achieve a better life in the traditional calculation, especially in the light load conditions. These special operating conditions are when the rolling surfaces (rails and rolling elements) are effectively separated by a smooth oil film and the contaminants are likely to be damaged. In fact, under the ideal conditions, the so-called permanent bearing life is possible.

After the bearing device, if not carefully stop the alignment, the alignment may cause the bearing to suffer additional loads, friction and vibration. These may accelerate fatigue and reduce bearing life, and may damage the use of other machine parts. In addition, increased vibration and friction can greatly increase energy costs and premature failure risk.

During the use of the regular operation of the bearing to the basic conditions to stop monitoring, such as temperature, vibration and noise measurement and so on. These regular inspections will detect potential problems early and will avoid unexpected machine downturns, enabling consumer solutions to be completed, and improving plant spending power and efficiency.

During the course of the operation, the track roller bearing request has the correct smoothness again, and its performance is complete. The smooth way of bearing, divided into smooth and smooth oil. In order to make the bearings play well, first of all, to choose the appropriate conditions of use, the use of the purpose of a smooth approach. If only thinking smooth, oil smooth smooth dominance. But the smoothness of the grease is able to simplify the expertise of the bearing around the structure.

When the track roller bearings will arrive at the end of their term of use, they should be switched off. Although the bearings can not be used again, but the correct removal of the original bearings, the timely exchange of new bearings, the extension of the life of the new bearings can play a very good role in promoting. First, the use of appropriate removal tools will help prevent damage to other machine components, and secondly, improperly removed technology may pose a hazard to the operator.


Copyright © Rihoo Industry (Hongkong) Co.,Limited All rights reserved.  
  • facebook
  • GooglePlus
  • link
  • print
  • twitter